−10°F to 50°F is the range. Holding a setpoint is the harder part.
Every unit we run holds anywhere from −10°F to 50°F, set on delivery. That flexibility creates an expectation that the number on the panel is the temperature of the product inside. It is not. The panel reads return air, and the gap between that number and the centre of a pallet is where loads get lost.
These are starting points, not a food safety plan. Your own requirements govern what you must hold.
| Frozen storage | −10°F to 0°F | Ice cream and frozen dessert want the colder end; frozen protein tolerates 0°F |
|---|---|---|
| Refrigerated food | 34°F to 40°F | Produce, dairy, deli and cooked-and-cooled product. The floor of this range gives margin for door openings |
| Bar and beverage | 34°F to 38°F | Kegs and bottled drinks. Colder than this is uncomfortable to serve, not safer |
| Medical and pharmacy | 36°F to 46°F | Driven by the product label, not by general food practice. Follow the manufacturer requirement |
| Holding and proofing | 45°F to 50°F | Chocolate work, tempered product, dough retarding where the recipe specifies it |
Two of these deserve a warning. Medical stock is governed by its own labelling, not by food service practice — if a vaccine says 2°C to 8°C, that is the requirement and this table does not override it. And −10°F is the floor of what a trailer does; blast freezing and dry ice work need different equipment.
Three reasons the number you read and the number that matters can differ by ten degrees.
The sensor sees air coming back to the evaporator, not the centre of a pallet six feet away. Air is easy to cool; a solid mass of product is not. The panel can read exactly on setpoint while the middle of a stack is still several degrees warmer.
A pallet of frozen protein carries hours of heat it must give up. Pulling a loaded trailer down from ambient is a different job from pulling an empty one down, and it does not happen in minutes.
Cooling happens by moving air across the load, not by proximity to the unit. Anything that blocks the path between the evaporator and the product — overloading, a wall of cartons against the front bulkhead, product flat on the floor — creates a warm zone the panel cannot see.
In order of how often we hear about them.
Every opening lets ambient air in and pushes cold air out along the floor. On a hot Inland Empire afternoon, recovery after an open door is measured in minutes. A site that expects constant access needs a second unit or a different plan, not a lower setpoint.
The single most common cause of a warm load in a correctly working trailer. Keep the floor return path clear and leave a gap at the front bulkhead so air can circulate down and back.
Dropping a warm load into a unit already at setpoint pulls the whole box up and takes hours to recover, with everything else in there along for the ride. Cool product before it goes in, or accept that the first day is a recovery day.
A unit swung from −10°F up to 40°F and back spends hours in transit through the middle of that range, and the load sits through all of it. Set it before loading and then leave it alone.
It is the difference between a trailer that is ready and a trailer that is on its way.
Pulling an empty trailer from ambient to a frozen setpoint takes hours, not minutes. That is why we deliver the day before an event, and why the trailer is running before we leave the site. If product arrives the same morning the unit is delivered, it goes into a box that is still coming down — and everything in it starts behind.
The practical rule: start the unit as soon as it is plugged in, close the door, and let it reach setpoint empty. Then load. A trailer that has been sitting at setpoint for an hour behaves completely differently from one that was started when the first pallet arrived.
There is a second reason to plan the extra hours. Defrost cycles run on a timer, and a unit that is working hard in a hot ambient pulls down more frost. Loading during a defrost cycle means warm air moving across new product — another argument for giving the box time.
One unit holds one setpoint. If the product needs two, that is a planning problem, not a setting.
An event serving ice cream and white wine cannot put both in one trailer. Either two units, or a negotiated compromise on one of the two — and the compromise is usually the dessert.
Different tolerances, different documentation, and often a requirement to keep them separate for traceability rather than temperature. Two units is usually the answer.
If staff work inside the trailer through a shift, the door is open constantly and the front of the box is warm by definition. Storage in one unit, working stock in another, is the arrangement that actually holds temperature.
Tell us what you are holding and when it goes in. We will set the unit before we leave.
Ask Us